Top One Innovator & Manufacturer of Circular Conveyor System in China!

Technical Guide

What are the Modular Conveyor Standard Components: Five Parts, Six Frozen Interfaces

Want to know more about our Modular Conveyor Standard Components?

Author:ChangMing, director of engineering department | 20th,sept 2026 | Category: Technical Guide

A modular circular conveyor is built from five part families rather than designed as one assembly. Every loop, whatever its size, is a front section, a rear section, one or more main frame sections, slide plates, and positioning modules.

The point of that decomposition is not manufacturing convenience. It is that the interfaces between the five are fixed, so a line can be lengthened, re-pitched or re-stationed without redesigning anything.

The five families in our Modular Conveyor Standard Components

Front section. The drive end. Carries the drive wheel, the power system and the arc at that end of the loop. Its straight-rail contribution is a fixed dimension, published per arc diameter, and it enters the loop length arithmetic as L1.

Rear section. The idler end. Carries the driven wheel and the opposite arc. Its straight-rail contribution enters the arithmetic as L3.

Main frame. The straight run between the two ends. Supplied in standard lengths, and a loop can use one section or several — the number of sections N and their individual lengths are both customisable. This is the component that absorbs a change in station count or pitch.

Slide plate. The carrier. Runs on the guideway on its roller set and presents a standard mounting pattern to the customer’s fixture.

Positioning module. The secondary positioning mechanism that takes the carrier from drive-train accuracy to stop accuracy — an order of magnitude. Two types, covered on Pneumatic Rod Positioning Mechanism and Cylinder Stop Positioning Conveyor.

What actually makes it modular

Five families is the visible part. The part that does the work is the set of interfaces that are held constant, because an interface that never changes is what lets everything on either side of it change freely.

Interface What it fixes What it lets you change freely
Front section to main frame Rail section, mounting height, bolt pattern Main frame length and count
Main frame to main frame The same, at every splice How the straight run is divided
Main frame to rear section The same Which end the drive sits at
Slide plate to guideway Roller set, groove angle, rail width Arc diameter, loop length
Slide plate to fixture The customer mounting pattern Fixture design, across the whole series
Positioning module to frame Mounting face and locator height Station count, station positions

Every one of those is frozen per series. That is why the range works the way it does, and it is also why crossing a series boundary is not a modification but a redesign — six interfaces move at once.

Modular conveyor standard components: five part families and the six frozen interfaces between them

The five part families with the six interfaces that are held constant per series.

Published standard components in our Modular Conveyor Standard Components

Series Arc diameter Front section Rear section Main frame Slider
V30 255 standard standard standard standard
V30 351 standard standard standard standard
V30 468 standard standard standard standard
V50 468 standard standard standard standard
V50 612 standard standard standard standard

Main frame and slider are standardised per series, not per arc diameter — one V30 main frame and one V30 slider serve all three V30 arcs. Only the end sections change with the arc.

That asymmetry is the whole design. Five combinations resolve to two main frame types, two slider types and five end-section pairs. The item with the highest turnover — the slider, which is the wear part and the one a plant is most likely to need in a hurry — is the one with the fewest variants. The items that vary with the arc are the ones that are replaced almost never.

What a change actually replaces

The most useful thing to know about a modular line is what each kind of change costs, because the answers are very different and they are not obvious from the parts list.

The change What it replaces What it leaves alone
Arc diameter, within the series Front and rear sections Main frame, sliders, positioning modules, fixtures
Station count Main frame length or count, sliders, positioning modules End sections, fixtures, mounting interface
Station pitch Main frame length, positioning module positions — and a linkage rod if one is fitted End sections, sliders, fixtures
Payload, beyond the series limit Everything Nothing

Changing the arc is the cheapest change in the range, which is fortunate, because opening out the arc is the usual answer to a cycle-time problem. It replaces two parts and touches no interface.

Changing the pitch is cheap on individual-cylinder positioning and expensive on a linkage rod, because the rod is pitch-specific hardware manufactured to the station spacing. A line expected to be re-pitched during its life should be specified with individual cylinders for that reason alone — Cylinder Stop Positioning Conveyor.

Change impact matrix for a modular circular conveyor, from arc diameter through to payload.

What each kind of change replaces and what it leaves alone.

What modularity buys, and where it stops

Interchangeability. The same slider fits any loop in its series. One spare slide plate covers every V30 line on the floor rather than one specific machine.

Delivery. Standard parts are made against a standard drawing, so lead time is stock-driven rather than design-driven. Note which family is the long pole for a given combination — the end sections are the arc-specific ones and are therefore the likeliest to govern.

Field reconfiguration — with three conditions attached that are easy to miss.

Adding two stations to an existing line means adding main frame length and sliders rather than re-engineering the loop. But the loop still has to close on a whole number of carrier pitches, so the added length is not free to be anything; the drive element has to be lengthened with it; and every added slider adds moving mass, which raises the accelerating torque and therefore the drive’s root-mean-square duty at the same index rate. A line that was comfortable before the change can be thermally marginal after it. The duty arithmetic is on Conveyor Cycle Time Calculation, and it is worth running before the extension is quoted rather than after it is fitted.

Maintenance scope. A damaged section is replaced as a unit. Any rail work invalidates the slide preload setting in that area — re-verify sliding resistance afterwards, per Eccentric Roller Adjustment, and note that on the 68° sizes there is no eccentric adjustment to fall back on.

The limits of the standard range in Modular Conveyor Standard Components

The standard modular range covers V30 and V50 only, in three and two arc diameters respectively. Everything outside that — V25, V44, the T series, the 200/300/400/500/600 arcs, the S-curve geometry — is available, but as a configured rather than a modular build, without the interchangeability and lead-time benefits above.

Between them the five combinations cover fixtures up to 500 mm and payloads up to 50 kg. Five standard combinations is a narrow range, and it is a deliberate one. V30 at 255/351/468 covers most sub-20 kg indexing lines; V50 at 468/612 covers most sub-50 kg ones.

If an application falls outside those, check first whether the requirement that pushes it outside is real. A fixture 10 mm too large for an envelope limit costs the whole modular benefit — the interchangeability, the spares position and the lead time — for 10 mm. That is usually a cheaper thing to change than the conveyor. Selection between the five, including the envelope and load-versus-speed exclusions, is on Modular Conveyor Selection.

Configuration within the range is quoted rather than ordered from a catalogue: the standard components are defined by family and arc diameter, and the part identifiers come with the quotation.

Where modular specification usually goes wrong

Treating a series change as a modification. It moves six interfaces at once and re-cuts the customer’s base plate.

Assuming an extension is free. Loop closure, drive element length and the drive’s thermal duty all move with it.

Specifying a linkage rod on a line that will be re-pitched. The rod is pitch-specific hardware.

Accepting a configured build to gain 10 mm of fixture envelope. Weigh what is being given up before the fixture is frozen.

Holding spares by line rather than by series. One slider covers every loop in its series; that is the point of the design.

How to make Circular Conveyor Maintenance and Troubleshooting: Commissioning Checks, Symptom Routes and the Pulse Calculation?

Sources and references

Primary sources are first-party. The five part families, the five published standard combinations, and the statement that the main frame and slider are standardised per series while the end sections vary with the arc are taken from the Circular Conveyor System catalogue (edition 2027.1) and from engineering confirmations recorded during its revision.

The interface table and the change-impact table are a restatement of that published asymmetry in the terms a designer uses. They introduce no figure that is not in the source.

Duty consequences of an extension follow from the root-mean-square torque treatment on Conveyor Cycle Time Calculation, applied qualitatively here rather than worked to a figure.

 

 

Prev:

Next: