Top One Innovator & Manufacturer of Circular Conveyor System in China!

Technical Guide

How to Check and Adjust Circular Conveyor Chain Tension?

How to check and adjust circular conveyor chain tension?

Author: ChangMing, Director of Engineering Department | Published: 12 October 2026 | Updated: 13 October 2026 | Category: Technical Guide

Circular conveyor chain tension decides whether every carrier on the loop starts and stops together. When it drifts out of range, the first sign is usually noise at the sprockets, and the later sign is drift at the stations.

What is circular conveyor chain tension? It is the pull in the drive chain that moves every carrier round the loop. It has two parts: working tension, created each time the drive accelerates and stops the carriers, and set tension, the small amount the take-up adds so the chain stays seated on its sprockets without slack.

Circular Conveyor Chain Tension: Chain-driven circular conveyor loop

Set tension should remove slack and nothing more, because extra tightness only adds wear. This guide covers chain-driven loops; belt-driven loops follow different rules. If loops are new to you, start with how a circular conveyor works.

What Circular Conveyor Chain Tension Means

On a loop, “tension” covers two different things. Many adjustment mistakes begin when they are treated as one.

Working tension: the pull the chain carries during each index

Working tension comes from the job itself. Each index accelerates the whole moving mass, meaning carriers, fixtures, parts and the chain, and then brings it to rest. Guide friction adds a smaller share.

So the pull peaks at the start and end of every index, not at steady speed. For a first estimate of chain pull, TallMan’s chain-driven circular conveyor page multiplies the weight of carriers and product by a friction coefficient of 0.2 to 0.4. Our chain drive loop calculation works through the full force from index time.

Because working tension follows from the moving mass and index time, the take-up cannot change it. It belongs to drive and chain sizing.

Set tension: what the take-up adds, and why it should be small

Set tension is the part that maintenance controls. Its only purpose is to take up the clearance in the chain joints, so the chain sits properly on the sprockets and does not slap.

Renold’s conveyor chain installation guide is clear on this point: pre-tension is not required, and over-adjusting shortens chain life. Set tension means “no slack”, not “as tight as possible”.

Tight side, slack side and where the take-up sits on a loop

The drive sprocket pulls one strand of the chain towards it, and that strand carries the working tension. The strand leaving the drive sprocket is the slack side, which is where any looseness collects.

For that reason, the take-up normally sits at the idler sprocket at the far end of the loop from the drive. Most of the chain on a carrier loop also runs in guide channels, so there is little free chain anywhere else.

Circular Conveyor Chain Tension :Tight side, slack side and take-up

The drive pulls the tight strand; slack collects on the other side, where the take-up sits.

Chain tension, slack, sag and elongation: four terms

The difference between chain tension vs chain elongation causes the most confusion. Tension is something you set, while elongation is something you measure.

Term What it is What changes it What you do about it
Working tension Pull in the chain while it indexes the carriers Moving mass, index time, friction Size the chain and drive
Set tension Tension the take-up adds to remove slack Take-up position Set at commissioning; check on schedule
Chain slack / sag Loose chain between supports Elongation, take-up movement Re-tension to the commissioning value
Chain elongation Longer pitch from pin and bush wear Running time, load, lubrication, dirt Measure; replace at the wear limit

Only set tension is adjusted in routine maintenance. Slack is the symptom you check for, and elongation is the cause you measure once re-tensioning stops working.

Why Chain Tension Matters More on an Indexing Loop

Chain tension for precision indexing conveyors needs more care than on a plain chain drive. A continuously running drive takes up its slack once, whereas an indexing loop takes it up and releases it at every start and stop.

Too loose: lost motion, slap and skipped teeth

With too much chain slack, the drive has to pull the slack out before the carriers move. As a result, the index can start late and overrun at the stop.

Between the sprockets, a loose chain can lift and slap against its guides. If the slack keeps growing, the chain can climb the sprocket teeth, a fault listed in the Tsubaki roller chain troubleshooting guide.

Some slack is normal, though. As Murtfeldt explains in its basics of a chain drive, the slack strand absorbs the small length changes that occur as each link wraps round the sprocket.

Too tight: bearing load, friction and faster wear

Over-tightening makes less noise, yet it shortens chain life. Higher pressure in every joint speeds up wear, and iwis notes in its maintenance notes that too tight and too loose both shorten chain life.

An over-tight chain also loads the sprocket shaft bearings and the drive, and friction marks on the chain rollers are a typical sign. Rising motor current is not proof of a tight chain, however, since guide-rail roller preload and friction from dirt or poor lubrication raise it too.

Circular Conveyor Chain Tension: Too loose vs too tight chain

The target is a band: no slack at the sprockets, and no extra preload.

How tension and elongation reach positioning accuracy

On a chain drive, published repeatability is ±0.03 mm with a positioning mechanism and about ±0.5 mm without one. Our guide to circular conveyor positioning accuracy explains where each figure comes from.

At stations without a mechanism, slack and wear show up directly in the stop position. At stations with one, the conical lead-in on the locating rod catches the carrier while it is still within the drive’s own tolerance and pulls it onto the datum. That margin is finite, so slack and wear gradually use it up.

Locator lead-in and positioning margin

Within the lead-in the locator corrects the stop; beyond it, it cannot.

Not every irregular stop is a chain fault. Overshoot or oscillation at the stop can also come from servo tuning or a high inertia ratio, which belongs to drive sizing rather than tension.

How Chain Tension Is Set: Take-Ups and Tensioners on a Loop

How much slack a chain has depends on its chain take-up. The type of take-up also decides how easily the chain can be over-tightened.

Screw take-up at the idler sprocket

A screw take-up moves the idler sprocket shaft with two adjusting screws. It is simple, and it holds its position firmly under index loads.

Its weakness is that it is easy to overdo. Renold warns that screw take-ups make over-tensioning easy, and uneven turns can also pull the shaft out of square.

Spring and pneumatic tensioners

A spring or pneumatic chain tensioner keeps pushing as the chain wears, so tension stays more even between checks. Renold advises limiting that force, because anything beyond what removes slack becomes preload.

iwis recommends mounting any tensioner on the slack side. On an indexing loop, the tensioner also needs enough stiffness; otherwise the load at each stop can push a soft spring back and let slack in.

Guide channels, catenary and long loops

A long loop multiplies every effect. Our 80-carrier long oval runs about 19.2 m of 20 mm-pitch chain, or 960 links, with twenty polymer guide channels and two tensioning assemblies rather than one. The 80-carrier long-loop example lists the full configuration.

The guide channels stop the chain lifting between sprockets, but their own wear adds slowly to positioning drift. They also leave most of the chain without a free span to measure. A catenary section, where the chain hangs in a defined loop, gives slack a known place instead.

Take-up type How it holds tension Suits Watch for
Screw take-up Fixed position, set by hand Indexing loops that need a firm setting Over-tightening; shaft out of square
Spring tensioner Constant spring force Steady, continuous running Pushed back by index loads
Pneumatic tensioner Constant air force Long loops with more elongation Air loss; force set too high
Catenary section Gravity sag in a set zone Long loops; easy access Space; must be on the slack side

In short, the screw take-up vs spring tensioner choice comes down to duty: a fixed setting for indexing, constant force for steady running.

Circular Conveyor Chain Tension: Four chain take-up types

A fixed setting suits indexing; constant force suits steady running.

How to Check Circular Conveyor Chain Tension: Step by Step

Because most of the chain sits in guides, checking chain tension on a circular conveyor works differently from a textbook chain drive. Everything depends on one reference, the commissioning value.

That value is the take-up setting recorded when the loop was set up and running correctly. Typically it is a measured take-up position or a slack measurement at a named point. If your documents do not record one, measure the current setting once the line is running well, and keep it as your reference.

Here is how to check chain tension on a circular conveyor:

  1. Lock out the drive and the air supply, following your site safety procedure.
  2. Return the loop to its origin so the same carriers sit at the same points each time.
  3. Compare the take-up position with its recorded mark or dimension.
  4. Check the slack at the point your documentation names, where the chain leaves its guides, for example at the idler sprocket or a catenary section.
  5. Inspect the guide channels along the whole run for slap marks or wear.
  6. Restore air and power and run at least one full lap, watching the returns and the start and stop of each index.
  7. Re-check positioning at the stations, then record the readings with the date and running hours.

 

Seven-step tension check

Every check starts with lockout and ends with positioning.

Why generic sag figures do not apply. Guides for open chain drives quote a sag of about 1–2% of the distance between sprockets (iwis). A guided loop has no single free span like that, so your loop’s own commissioning value is the only reliable reference.

How to Adjust Circular Conveyor Chain Tension Without Over-Tightening

Knowing how to adjust conveyor chain tension matters less than knowing where to stop. When a check shows slack beyond the commissioning value, adjust circular conveyor chain tension with a screw take-up as follows:

  1. Lock out as in the check above, then loosen the take-up locknuts.
  2. Turn both screws equally, a little at a time, so the idler shaft stays square.
  3. Stop at the commissioning value, not beyond it.
  4. Lock the screws, run at least one full circuit, then check again.
  5. Re-verify the origin and the positioning at each station before production restarts.

New chains bed in during their first hours of running. Renold advises running a new chain unloaded for 8 to 24 hours and then re-checking. Our long-loop calculation guide makes the same point: re-check after run-in, then at intervals set by measured drift.

Tip: mark the take-up position after every adjustment. The marks show how fast the chain is growing and when the travel will run out.

When the take-up has no travel left, the chain has grown too far for adjustment to help, and the next step is to measure elongation.

Why you should not remove a link on a carrier loop

On an ordinary chain drive, taking out a link is a common way to recover slack. On a carrier loop, however, it does not work.

Carriers attach at a fixed number of links. On the 80-carrier loop that is 12 links per carrier, or 240 mm at 20 mm pitch. On the precision indexing loop each station pitch is about 762 mm, which equals 40 pitches of 19.05 mm chain, as the carrier pitch and drive pitch section of our design guide explains.

Remove one link and every carrier after it shifts. A cranked (half) link is no answer either, since iwis notes it cuts breaking strength by about 20%. On a carrier loop, an elongated chain is replaced, not shortened.

Screw take-up and why not to remove a link

Equal turns keep the idler shaft square; removing a link shifts every carrier after it.

Chain Elongation: When Re-Tensioning Is No Longer the Fix

Why does a conveyor chain lose tension? Mostly because it gets longer. The cause is wear between pins and bushes rather than stretch, as Rexnord explains in its note on why chain elongation is joint wear.

Re-tensioning hides elongation until the take-up runs out of travel, so a circular conveyor chain needs measuring as well as tension adjustment. Wear rate depends heavily on lubrication and cleanliness, which is why Renold’s maintenance guidance covers lubrication alongside take-up adjustment.

How to measure chain elongation

Measure with the chain under tension, on a straight run, over as many pitches as you can reach. Rexnord recommends at least four pitches and ideally about 3 m of chain. Then work out the percentage:

Elongation (%) = (measured length − number of pitches × nominal pitch) ÷ (number of pitches × nominal pitch) × 100

For example, 50 pitches of 20 mm chain should measure 1,000 mm, so a reading of 1,010 mm means 1% elongation. Nominal pitch is 20 mm on our modular range and 19.05 mm for 12A chain to ISO 606 roller chain dimensions.

On a guided loop, choose a straight stretch on the pulled side where the chain is accessible, and always measure at the same place so readings can be compared over time.

Measuring chain elongation

Elongation is joint wear, measured over many pitches under tension.

Elongation limits by duty

Conveyor chain wear limits depend on what the chain has to do. Chain makers publish these typical values:

Duty Typical elongation limit Source
Adjustable-centre drives (general) About 3% iwis; Rexnord (2.5–3%); Diamond Chain
High-performance drives About 2% iwis
Fixed-centre drives 1.5% Diamond Chain maintenance guide
Chain that itself does the positioning or synchronising About 1% iwis; Murtfeldt

Which row applies to a loop depends on its stations. Where the chain alone sets the stop position, as at stations without a positioning mechanism, the stricter rows are the relevant ones.

Where every precision station has a mechanism, the chain only needs to deliver each carrier inside the locator’s lead-in. In that case the chain maker’s limit for the drive geometry applies. Agree the replacement limit for your loop with your supplier and record it next to the commissioning value.

What elongation does to carrier pitch and station positions

As the chain grows, the spacing between carriers slowly increases, and each index stops a little further from the datum. A positioning mechanism keeps pulling each carrier back onto the datum, so repeatability holds for a while.

Once the offset approaches the edge of the lead-in, though, the locator can no longer correct it. When you replace the chain, inspect the sprockets as well, because Renold advises against running a worn chain on new sprockets, or the reverse.

Chain Tension Problems: Symptom, Cause and First Check

Most circular conveyor chain tension problems show up as one of a few symptoms. Work through them in this order, because some look like chain faults but start elsewhere, as our symptom routes show.

Symptom Likely cause First check
Chain slaps or lifts between sprockets Tension loss; worn or displaced guide channels Re-tension to the commissioning value; inspect channels
Carriers slip or the line loses steps Chain take-up, or load beyond the capacity curve Take-up position; payload and speed
Late start and overrun at each index Chain slack Take-up; then elongation
Overshoot or oscillation at the stop, tension correct Servo tuning or inertia ratio Drive settings; see the drive sizing steps
Stops drift slowly over weeks Chain elongation; locator wear Measure elongation; compare several carriers
Noise through one return Debris; carrier rollers; sprocket bearing Clean the return; inspect that carrier and bearing
Chain climbs sprocket teeth Excess slack or worn sprocket Tension; sprocket tooth shape
Motor current rising over weeks Rail roller preload, dirt or lubrication; tight chain Trend the current; check preload, then the take-up

If wear marks on the rail itself are the problem, see our guide to circular guide rail wear.

Chain still losing tension after adjustment? Send us the details listed below.

Request a Quote — Circular Conveyor System

How Often to Check Chain Tension on a Circular Conveyor

A short schedule catches most problems early, and it fits into a wider circular conveyor chain maintenance routine, set out in full in our circular conveyor maintenance schedule.

When What to check Source
After run-in (new chain or new loop) Tension and take-up position Renold; C Motion
Quarterly or half-yearly Chain tension, rollers, origin position C Motion maintenance guide
Yearly, or when the take-up runs short Elongation measurement Renold (annual inspection)
After any rework Tension, origin and station positioning C Motion maintenance guide
Slap, drift or skipped steps Full check and elongation Troubleshooting table above

Once the chain has bedded in, base the interval on operating hours, cycle count, load and contamination rather than the calendar. A loop indexing every half second sends each carrier round far more often than one indexing every few seconds, so its chain wears faster.

Chain Tension on Two Real C Motion Loops

Two of our loops show how chain tension practice follows loop length and duty.

Loop Chain Carriers / pitch Tension provisions What matters most
80-carrier long oval 20 mm pitch, 960 links (about 19.2 m) 80 carriers at 240 mm (12 links) Two tensioning assemblies; 20 guide channels Elongation adding up over 960 links
10-carriage precision indexing loop 12A, 19.05 mm pitch About 762 mm station pitch (40 chain pitches) Short chain on a ten-carriage loop Stop position at every station

On the long oval, small amounts of wear add up across nearly twenty metres of chain. At a 0.5 s index, each carrier completes a lap in about 40 seconds, so the chain articulates over its sprockets many times an hour. That is why the loop carries two take-ups, guides the chain along its whole length, and calls for elongation readings rather than calendar checks.

The precision indexing circular conveyor has a short chain but a demanding job. There, chain tension for precision indexing conveyors comes down to keeping the stop position inside the locator’s lead-in at every station, which makes the take-up marks and elongation readings the key records.

Two real C Motion loops

Tension practice follows loop length and duty.

See the full chain-driven circular conveyor range, or download the circular conveyor catalogue.

What to Send Us If Your Chain Keeps Losing Tension

If the chain on your loop keeps losing tension, these details let our engineers find the cause quickly:

  • Loop model or drawing number, so we know the chain and take-up design.
  • Chain size and pitch.
  • Running hours since installation or the last chain change.
  • Take-up position now compared with its commissioning mark, with a photo.
  • Elongation reading and the number of pitches measured.
  • Symptoms (slap, drift, skipped steps) and where on the loop they occur.
  • Index time and payload.
  • Photos of the sprockets and guide channels.
  • Environment: dust, washdown or temperature.

Service information checklist

Send these details if the chain keeps losing tension.

Mark anything you do not know as open. Every quotation includes a layout drawing, which helps when a replacement chain or a take-up change is needed. Request a Quote — Circular Conveyor System.

Circular Conveyor Chain Tension FAQ

What is chain tension on a circular conveyor?

It is the pull in the drive chain: working tension from indexing the carriers, plus a small set tension at the take-up to remove slack. The four terms table shows how it differs from slack and elongation.

How do I check chain tension on a circular conveyor?

Lock out, return the loop to origin, and compare the take-up position and slack with the commissioning value. Then run a full lap and re-check positioning, as in the step-by-step check.

How much chain tension does a circular conveyor need?

Just enough to remove slack at the sprockets. Extra tightness adds wear without improving accuracy, so set it to the value recorded for your loop at commissioning rather than a generic sag figure.

Why does circular conveyor chain tension drop over time?

Mainly because pin and bush wear makes the chain longer, while new chains also bed in during their first hours. Re-check after run-in, then as measured drift requires, and measure elongation when the take-up runs short.

Can I remove a link from a circular conveyor chain to take up slack?

Not on a carrier loop. Carriers attach at a fixed number of links, so removing one shifts every carrier after it. Replace the chain when it reaches its agreed wear limit.

How much chain elongation is too much on an indexing conveyor?

It depends on the stations. Where the chain alone sets the stop, the stricter positioning limits apply; where every precision station has a positioning mechanism, the chain maker’s limit for the drive applies. Agree the figure with your supplier.

Does chain tension affect circular conveyor positioning accuracy?

Directly at stations without a positioning mechanism. With a mechanism, repeatability holds until slack or wear pushes the carrier beyond the locator’s lead-in, as our positioning accuracy guide explains.

When should circular conveyor chain tension be re-checked after installation?

After the run-in period, then quarterly or half-yearly, and again after any rework or symptom. Long or fast-indexing loops may need shorter intervals.

Conclusion: Just Enough Tension, Checked Against the Commissioning Value

Set tension exists to remove slack, and anything beyond that only shortens chain life. On an indexing loop, the bigger long-term threat is elongation, which you measure against an agreed limit instead of re-tensioning it away.

Chain-driven loop drifting or losing tension?

Send us your loop details and readings, and our engineers will review your circular conveyor chain tension and quote any parts needed.

Request a Quote — Circular Conveyor System

Follow C Motion: video gallery · LinkedIn

About the author. ChangMing leads the engineering department at C Motion and has 10 years of experience in the industry, working on the design, assembly and commissioning of circular conveyor loops.

Prev:

Next: